Tags

, , ,

Well, I could hardly leave the poor thing ticking away, whilst laboring against the possible impediment of increasingly viscous 40 year old oil and so, motivated by an offer to buy my watch, I’ve set about the task of giving the movement its first service.   I tend to approach the servicing of quartz movements with a certain amount of trepidation, not because they are any more mechanically complex than the mechanical pieces I favour – they are evidently not – but because their operation depends so much on the correct functioning of key parts over which I have no facility to exert influence. A blown circuit or a failed coil will not bend to my will. They will remain blown or failed and the watch inoperable unless I can source replacements. However, with this particular example functioning correctly, the task at hand reduces to dismantling the movement, cleaning it, and reassembling the parts, freshly lubricated, as required.

So as usual, we start with the movement out, and the hands set to 12 to aid their removal:

Seiko King Quartz dial

The removal of the hands requires some care both because of the immaculate state of the dial but also the fact that, being effectively new, they are a little more reluctant to release their grip on the hour wheel and cannon pinions. Removal of parts from the calendar and train sides of the movement proceeded without incident but in familiarising myself with its architecture, I was left with the impression that this is a modern and sophisticated design including some neat features.

4822A calendar

Some of the layout on the calendar side is familiar but the keyless works is quite different from that of any of the Seiko mechanical movements I’ve worked on from the same era. The train side is less familiar of course because the operational heart is the quartz oscillator, circuit and coil rather than mainspring, escapement and balance.

4822A dismantling

One particularly striking feature of the watch design can be found in the third wheel bridge, seen top side in the photo, top right, above. The appearance of the bridge looks somewhat unusual, in particular the additional plate sitting atop the fourth wheel jeweled-bearing – not something we would expect to encounter on a mechanical watch. In looking at the underside of the bridge, we can see what’s what. The plate supports a jeweled jumper, there to regulate the movement of the seconds hand, acting as it does upon the teeth of the fourth wheel.

4822A third wheel bridge

The half-way point then it reached with the mainplate naked, free from all its fixtures and fittings.

Seiko 4822A mainplate

Into reverse gear with the parts now clean, we start by placing the stem and clutch before fitting the date corrector rocker and wheel, the setting lever axle and lever.

4822 setting lever

The intermediate wheel for date correction and the setting wheel move into position next, secured by the setting wheel ring, with this part of the process completed by fitting the setting lever axle spring.

4822 setting wheels

The whole shebang looks very neat and robustly engineered, with no obvious weak links. Turning the movement over, we start with the centre wheel, followed by the rotor stator and step rotor.

4822 rotor stator

In cleaning and handling the magnetic step rotor, we have to be very careful to make sure no magnetic debris has adhered to the rotor. In this instance, it’s clean as a whistle. The centre wheel bridge comes next and in fitting it we need to take care to make sure that the driving pin emerging from the rear of the setting lever is correctly engaged with the second setting lever.

4822 centre wheel bridge

This arrangement provides the key to the rather clever rapid advancement of the seconds hand when the crown is pulled out to the time setting position. In pulling the crown out, the driving pin acts upon the second setting lever, moving its hammer against a cam on the rear of the second setting wheel.

4822 second setting wheel

Depending on where the seconds hand is on its journey around the dial, interaction of the hammer with the cam will move the seconds hand onto the next 10 second position (10, 20, 30, 40, 50 and 60). Thus, if the crown is pulled out at 51 seconds, the seconds hand will leap forwards to the zero position, saving you the tedium of having to wait those extra 9 seconds. The second part of this operation is the simultaneous movement of the reset lever against the reset pin on the electronic circuit, stopping the watch.

4822 second setting

The fiddliest bit now follows. In go the third and fourth wheels

4822 train wheels

followed by that cool second setting wheel and its cam

Seiko 4822 train wheels

and several minutes cursing follow while I try to will the third wheel bridge to engage with the arbors of four separate wheels, without having the means to manipulate them in the way you can in a mechanical watch by rotating the mainspring barrel. Somehow though, they all eventually locate and I rather gingerly tighten down the bridge in stages making sure that everything is properly in position.

Seiko 4822 third wheel bridge

With no fowl-ups, the only remaining task is to refit the circuit and battery insulator, the cannon pinion, minute, hour and date driving wheels,

Seiko 4822 calendar parts

followed by the setting lever spring and remaining calendar parts.  The dial and hands complete the deal before refitting the movement to the case. We finish by making sure that all of the functions work correctly (which they do) and we are done.

Seikko 4822 King Quartz

 

Advertisements